THERMAL BOTTLE WRAP WITH POWER SUPPLY – AU
$35.68
Plug: AU
Additional information
| Plug |
|---|
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
TVB-161 20 inches 508mm KIT INCLUDES 3A POWER
ThermalVATBAND is a simple adhesive tape 20 inches long by 1 inch 508mm when applied to a 3D resin printer VAT, will maintain an ideal temperature for your photopolymer resin, despite the ambient temperature. ThermalVATBAND regulates temperature using two smart thermostats that can be easily attached and are safe to the touch. Using ThermalBand is efficient and cost-effective, with only 12 watts of power costing significantly less than any heater on the market.
- Vatband uses a solid silicone wire, making it durable when an acrylic cover is placed on top.
- Vatband does not have to cover 100% of your VAT; you can still maintain the required heat because the Z axis mixes the resin to ensure homogeneous heat coverage. (See infrared imaging.)
One power source can power up to three VATBANDS using a splitter. When sharing one power adapter with three VATBANDS, be mindful that power is distributed equally and maximum power should not exceed 3 on the power band. If you see the power adapter light blink, you should turn down the power until it stops blinking. Because the power is shared, your maximum temperature will range from 75°F to 80°F, whereas one powered VATBAND can reach up to 90°F, and you can use the power adapter to its full capacity.
- Vatband uses a solid silicone wire, making it durable when an acrylic cover is placed on top.
- Vatband does not have to cover 100% of your VAT; you can still maintain the required heat because the Z axis mixes the resin to ensure homogeneous heat coverage. (See infrared imaging.)
One power source can power up to three VATBANDS using a splitter. When sharing one power adapter with three VATBANDS, be mindful that power is distributed equally and maximum power should not exceed 3 on the power band. If you see the power adapter light blink, you should turn down the power until it stops blinking. Because the power is shared, your maximum temperature will range from 75°F to 80°F, whereas one powered VATBAND can reach up to 90°F, and you can use the power adapter to its full capacity.
TVB-V2 20 INCHES POWER ADAPTER INCLUDED
ThermalVATBAND band that is 20 inches long and 1 inch wide, with a direct female jack connection in a low-profile box on the VATBAND itself. The TVB-161 appears to have wires hanging from the VAT and a female jack at the end of the wire. It's possible to split the power source of the thermal VAT band and share it with another VAT band or a bottle warmer, allowing up to three products to be powered at the same time.
- Includes accessories pack ( sticker over VATBAND and thermostat sticker that can be applied directly on TVB (consider the fact that the temperature will be higher outside versus the resin inside by approximately 5 degrees). Aluminum tape is placed on stress points on curves and edges, and after pulling the jack area, a strip is applied to the cold zone on the front and back of the box. Before applying the VAT, use a scuff pad aggressively clean the VAT surface with IPA to remove any remaining resin.
TVB-V3 34 inches VATBAND ONLY
Thermalvatband is 32 inches by 1 inch (81.28 centimeters) with a revised direct connect to power adapter. Increasing reaction time and heat by 10%. The advantage to a direct connection is resin drips will not cause any issue with contact points.
- Includes an accessory pack (sticker over the VATBAND and an extra sticker for the thermostat (aluminum tape), a thermometer, and a scuff pad to clean the VAT before application.
- You may have to place a 1/8-inch diameter hole in the back of your case to allow power access.
