TVB-161 20 inches 508mm KIT INCLUDES 3A POWER
$40.00
ThermalVATBAND is a simple adhesive tape 20 inches long by 1 inch 508mm when applied to a 3D resin printer VAT, will maintain an ideal temperature for your photopolymer resin, despite the ambient temperature. ThermalVATBAND regulates temperature using two smart thermostats that can be easily attached and are safe to the touch. Using ThermalBand is efficient and cost-effective, with only 12 watts of power costing significantly less than any heater on the market.
– Vatband uses a solid silicone wire, making it durable when an acrylic cover is placed on top.
– Vatband does not have to cover 100% of your VAT; you can still maintain the required heat because the Z axis mixes the resin to ensure homogeneous heat coverage. (See infrared imaging.)
One power source can power up to three VATBANDS using a splitter. When sharing one power adapter with three VATBANDS, be mindful that power is distributed equally and maximum power should not exceed 3 on the power band. If you see the power adapter light blink, you should turn down the power until it stops blinking. Because the power is shared, your maximum temperature will range from 75°F to 80°F, whereas one powered VATBAND can reach up to 90°F, and you can use the power adapter to its full capacity.
Description
The ThermalVATBAND kit includes the 20×1-inch 508mm TVB-161 and a power adapter up to 240 volts, making it ideal for use in any country with a plug conversion. Power adapter comes with US plug you must choose your country plug conversion plug.
The output operates at a safe range of 12 V/3 A without the risk of damaging FEP or plastic VATS.
The band itself features a flexible thermostat that allows you to maximize the temperature in extreme cold conditions by flexing the thermostat away from the VAT.
The recommended optimum thermostat position is touching the wall. This will automatically regulate the ideal VAT temperature, ranging from 22 °C (70 °F) to 32 °C (90 °F).
– In extreme cold weather, we do recommend a foam tape applied under the case for a better seal, preventing cold air from coming inside.
-Aluminum tape is an alternative tape that can be used on corners or on the interior vat of plastic vats to create a resin and IPA proof seal that allows heat to conduct safely.
To maintain the ideal temperature and match the temperature of the liquid resin, the build plate must be submerged in the vat filled with resin after each use. Following these guidelines will prevent the build plate from rapidly cooling the resin’s temperature.
– The thermostat reading is from the direct heat of the VATBAND, and the resin will be 5 degrees less. When you see the thermostat go black, the temperature cycling process is rapid, and the thermostat will have a slight delay in reading. Rest assured that your ideal temperature range is cycling, which will prevent FEP from shrinking.
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
TVB-161 20 inches 508mm VATBAND ONLY
ThermalVATBAND is a simple as adhesive tape that applied to a 3D resin printer VAT will maintain an ideal temperature for your photopolymer resin, despite the ambient temperature. ThermalVATBAND regulates temperature using thermostats that can be easily be attached and are safe to the touch. Using ThermalVATBAND is efficient and cost effective, costing $.85 per 24hr compared to $4.50 per 24hr for typical 120V conventional heaters.
TVB-V2 20 INCHES NO POWER ADAPTER
Thermalvatband 20 inches by 1 inches ( 50.8 centemeters) with connection bay 3 ( 2.5 centemeters)
- Includes accessories pack ( sticker over VATBAND and extra sticker for thermostat (aluminum tape) thermometer and scuff pad to clean VAT before appication.
Ideal for printers: Saturn S, Mono X all medium and small VATS.
TVB-V2 20 INCHES POWER ADAPTER INCLUDED
ThermalVATBAND band that is 20 inches long and 1 inch wide, with a direct female jack connection in a low-profile box on the VATBAND itself. The TVB-161 appears to have wires hanging from the VAT and a female jack at the end of the wire. It's possible to split the power source of the thermal VAT band and share it with another VAT band or a bottle warmer, allowing up to three products to be powered at the same time.
- Includes accessories pack ( sticker over VATBAND and thermostat sticker that can be applied directly on TVB (consider the fact that the temperature will be higher outside versus the resin inside by approximately 5 degrees). Aluminum tape is placed on stress points on curves and edges, and after pulling the jack area, a strip is applied to the cold zone on the front and back of the box. Before applying the VAT, use a scuff pad aggressively clean the VAT surface with IPA to remove any remaining resin.
TVB-V3-KIT WITH POWER ADAPTER
Thermalvatband is 32 inches by 1 inch (81.28 centimeters) with a revised direct connect to power adapter. Increasing reaction time and heat by 5%. The advantage to a direct connection is resin drips will not cause any issue with contact points.
- Includes an accessory pack (sticker over the VATBAND and an extra sticker for the thermostat (aluminum tape), a thermometer, and a scuff pad to clean the VAT before application.
- You may have to place a 1/8-inch diameter hole in the back of your case to allow power access.
